Beyond the Gritter's Route: Winter-Proofing New Brickwork, Steps and Paving
Photo: Evelyn Simak , CC BY-SA 2.0, via Wikimedia Commons
Most homeowners think about winter damage in terms of frost. In practice, on many UK sites, the more persistent aggressor is salt. Grit spread on roads and pavements is thrown up by tyres, washed across footways and carried into entrance areas, where it dries on brickwork, mortar joints, steps and paving. Add repeated freezing and thawing, and new construction can begin to show its weaknesses within a single season.
The sensible response is not to specify an impregnable surface. It is to recognise where salt-laden water will collect, splash and dry, then detail the work so those zones can cope. That means making decisions at drawing stage, not waiting until a homeowner notices white staining or a crumbling step in spring.
Define the salt zone before setting out
Salt exposure is rarely uniform. A wall facing a busy road may receive spray every time a gritter passes, while a sheltered rear elevation a few metres away remains comparatively clean. A driveway that falls towards the house concentrates run-off at the threshold. A bin store beside a pavement can become a trap for slush thrown from passing feet.
Before work starts, mark the likely salt zone on the site plan. Consider prevailing wind, kerb lines, vehicle turning areas, the route of the local gritter and the fall of hard surfaces. Ask where water will sit, where it will splash and where it will dry. Those answers should influence the choice of facing brick, the height of the damp-proof course, the detail at door thresholds and the position of drainage.
This is also the point to discuss maintenance expectations. A surface that will be regularly splashed with salt is not the place for the most porous paving or the softest reclaimed brick, however attractive they may look in a brochure.
Choose materials for wet, salty cycles
For new brickwork, frost resistance and salt tolerance should be treated as part of the specification, particularly below and just above ground level. Engineering bricks and facing bricks with a proven frost rating are generally more suitable for plinths, piers and walls close to salted paving than soft, highly absorbent units. Reclaimed bricks can work well in sheltered positions, but their variability makes them a poorer choice for the splash zone unless each unit has been assessed.
Mortar deserves equal attention. It should be compatible with the masonry, not stronger than necessary. A dense, impermeable mortar can force moisture to migrate through the brick instead, increasing the risk of spalling. Joints should be finished neatly and consistently; recessed or damaged joints hold water and give salt a place to concentrate.
Concrete paving, flagstones and steps should be selected for frost resistance and suitable for external use. Avoid mixing products intended for sheltered domestic paths with a driveway that receives winter traffic and de-icing salts. Where concrete is mixed on site, follow the supplier's guidance carefully and do not add chloride-based accelerators. In new concrete, chlorides can contribute to reinforcement corrosion and surface deterioration.
Plinths, thresholds and the splash shadow
Many winter defects begin in the first 300mm above ground. This is the splash shadow: the band that receives the most spray, run-off and grit. A robust plinth detail, a damp-proof course kept clear of paving and a sensible separation between finished ground level and internal floor level all help.
Door thresholds are especially vulnerable. If external paving is laid tight to a timber threshold, or if the fall directs water towards the door, salt-laden water can sit against vulnerable materials. A threshold should shed water outwards, with a suitable drainage channel or fall where exposure is high. Step nosings should be durable and firmly bedded, not reliant on a thin mortar skim that will be abraded by grit and foot traffic.
Where a wall meets paving, avoid bridging the damp-proof course with soil, mortar or a raised patio. Keep the external level below the required clearance and make sure the detail can be inspected later. Good practice is not merely about keeping water out today; it is about allowing a homeowner or surveyor to see what is happening after the first winter.
Drainage: move salty water away from the building
Salt damage is often worsened by poor drainage. Water that ponds against a plinth will keep the masonry wet, and repeated wetting and drying increases the opportunity for salt crystallisation and frost action. Paving should fall away from the building, and gullies, channels and soakaways should be positioned so that run-off from salted areas does not discharge against walls or foundations.
Permeable paving can be useful, but it is not a universal answer. In heavily salted areas, the surface and sub-base still need appropriate design, and the system must be maintained. A blocked permeable surface behaves like any other blocked drain. For entrance areas, a linear channel across the doorway can intercept water before it reaches the threshold, provided it has a clear outlet and can be cleaned.
Protect new work during construction
Winter working brings its own risks. Fresh mortar should be protected from freezing, and newly laid concrete should not be exposed to frost or de-icing salts before it has gained adequate strength. Temporary covers, insulated blankets and sensible sequencing are part of good construction practice, not optional extras.
Keep stockpiles of grit and salt away from new paving and masonry. Do not use rock salt to clear ice from freshly completed concrete or paving unless the manufacturer specifically permits it. Where a site is muddy, provide a clean route for deliveries and foot traffic so that salt and grit are not trampled across finished surfaces. At handover, leave the homeowner with clear guidance on suitable de-icing products and the first-winter precautions recommended for the materials used.
A post-winter inspection that means something
Once the main gritting season has passed, usually by early spring, carry out a simple inspection. Look along the plinth and the lower courses of brickwork for efflorescence, surface flaking, crumbling mortar or damp patches that do not dry. Check steps for loose nosings, cracked edges and movement. Examine paving joints and thresholds for ponding, settled areas or salt staining. Clear gullies and channels, and confirm that water still runs away from the building.
Photograph anything that concerns you and compare it with the same detail the following year. Small repointing, a localised repair to a step or an adjustment to drainage is far cheaper than rebuilding a saturated plinth. The aim is not to eliminate winter, but to make sure the building is designed to meet it and inspected while small faults are still small.